| SL-AG-5 |
ENGINE MOUNT INSPECTION |
| SL-AG-6 |
ELEVATOR PULLEY INSTALLATION |
| SL-AG-7 |
AILERON PUSH-PULL SYSTEM |
| SL-AG-8 |
AILERON SPAR INSPECTION AND HINGE MODIFICATION |
| SL-AG-9 |
STEEL AILERON HINGE INSTALLATION |
| SL-AG-10 |
MARLEX FAIRLEAD AVAILABILITY |
| SL-AG-11 |
ENGINE MOUNT PREVENTIVE MAINTENANCE |
| SL-AG-12 |
OIL TANK STRAP REINFORCEMENTS |
| SL-AG-13 |
INSPECTION OF VERTICAL FIN STRUCTURE |
| SL-AG-14 |
S-2B ENGINE MOUNT INSPECTION |
| SL-AG-15 |
S-2B ENGINE MOUNT |
| SL-AG-16 |
OIL TANK STRAPS |
| SL-AG-17 |
S-2B ENGINE MOUNT |
| SL-AG-18 |
WING ATTACH ANGLES |
| SL-AG-19 |
FIN AND RUDDER HINGES |
| SL-AG-20 |
LANDING GEAR |
| SL-AG-21 |
AILERON STOP CABLE |
| SL-AG-22 |
ELEVATOR TRIM TAB RIB REPLACEMENT |
| SL-AG-23 |
MAIN SPAR AT FUSELAGE SIDE |
| SL-AG-24 |
REAR PROP CONE |
| SL-AG-25 |
FUEL SYSTEM |
| SL-AG-26 |
AILERON CONTROL STOP CABLES |
| SL-AG-27 |
CONTROL STICK STOP BOLTS |
| SL-AG-28 |
TAILWHEEL TRUNNION ATTCH SHAFT |
| SL-AG-29A |
WING CENTER SPLICE |
| SL-AG-30 |
RUDDER CABLE WEAR |
| SL-AG-31 |
AILERON BELL CRANK ATTCH ANGLES IN NEW AILERON CONTROL SYSTEM |
| SL-AG-32 |
CHANGE OF POSITION OF GROUND WIRE ATTACHMENT |
| SL-AG-33 |
HORIZONTAL STABILIZER LEADING EDGE VIBRATION |
| SL-AG-34 |
EXCESSIVE PIN WEAR ON ATTCH POINT OF LOWER TAIL FLYING WIRES |
| SL-AG-35 |
CORROSION PROBLEM WHEN USING HIGHLY CORROWSIVE MATERIALS |
| SL-AG-36 |
REPLACEMENT OF LOWER SPAR CAP |
| SL-AG-37 |
INSPECTION NOTICE - FUSELAGE FRAME |
| SL-AG-38 |
BRACING OF WELDED HOPPER IN EARLY S-2C AIRCRAFT |
| SL-AG-39 |
FUEL VENT OVERFLOW |
| SL-AG-40 |
MODIFICATION OF BRAKE PUSH ROD |
| SL-AG-41 |
ADDITIONAL BOOM SUPPORT |
| SL-AG-42 |
LANDING GEAR AXLE, THRU BOLTS |
| SL-AG-43 |
WIRE DEFLECTOR CABLE ASSEMBLY |
| SL-AG-44 |
RUDDER CONTROL CABLE FRAYING |
| SL-AG-45 |
FUEL GAGE MALFUNCTION |
| SL-AG-46 |
BRAKE TENSION ROD - P/N 5-7066 |
| SL-AG-47 |
ELEVATOR TRIM CABLE |
| SL-AG-48 |
TAIL WIRE BRACKET - UPPER FRONT FIN-REPLACEMENT |
| SL-AG-49 |
FIRE EXTINGIUSHER PLACARD INSTALLATION |
| SL-AG-51 |
RE-POSITIONING OF VOLTAGE REGULATOR ASSEMBLY |
| SL-AG-52 |
STARTER GROUND WIRE BRACING |
| SL-AG-53 |
TRIM TAB END RIB |
| SL-AG-54 |
MAIN GEAR UPPER SHOCK ATTACH FITTING |
| SL-AG-55 |
HORIZONTAL STABILIZER ATTACH BOLTS |
| SL-AG-56 |
THROTTLE CONTROL BELLCRANKS |
| SL-AG-57 |
METALLIC BRAKE LININGS |
| SL-AG-58 |
HOPPER BAFFLE ATTACH T-ANGLE |
| SL-AG-59 |
HOPPER BAFFLE ATTACH T-ANGLE (REAR WALL) |
| SL-AG-60 |
FUEL GAUGE TANK UNIT |
| SL-AG-61 |
AILERON BAY SKINS |
| SL-AG-62 |
TAILWHEEL HOUSING CASTING |
| SL-AG-63 |
WIND GUST DAMAGE TO AILERONS |
| SL-AG-64 |
ELEVATOR TRIM TAB MECHANISM |
| SL-AG-65 |
SUPPORT BRACKET FOR REVERSE CURRENT RELAY AND VOLTAGE REGULATOR |
| SL-AG-66 |
NIGHT LIGHTING SYSTEM AAND VOLTAGE REGULATOR CIRCUIT INTERACTION |
| SL-AG-68 |
SPRAY PRESSURE LINE FLEX HOSE |
| SL-AG-69 |
WING LEADING EDGE RIB RIVLETS |
| SL-AG-70 |
REPLACEMENT OF BRAKE ASSEMBLY O-RINGS |
| SL-AG-71 |
MODIFICATION OF EXHAUST MANIFOLD OUTLET |
| SL-AG-72 |
WIND GUST DAMAGE TO AILERONS |
| SL-AG-73 |
REPLACEMENT OF TAIL WHEEL SHOCK STRUT EXTENSION ASSEMBLY |
| SL-AG-74A |
MASTER RELAY CONTROL CIRCUIT |
| SL-AG-75 |
CARBURETOR AIR BOX CONTROL CABLE CLAMP REPLACEMENT |
| SL-AG-76 |
CARBURETOR REPLACEMENT |
| SL-AG-77 |
CARBURETOR AIR INLET SCOOP ASSEMBLY REPLACEMENT |
| SL-AG-78 Rev 1 |
COLLECTOR RING REPLACEMENT |
| SL-AG-79 |
CARBURETOR HEAT MODIFICATION |
| SL-AG-80 Rev 1 |
CRANKCASE AIR/OIL SEPARATOR INSTALLATION |
| SL-AG-81 Rev 1 |
IMPROVED FLIGHT CHARACTERISTICS |
| SL-AG-82 |
TAIL WHEEL TRUNNION ASSEMBLY MODIFICATION |
| SL-AG-83 |
REWORK OF VERTICAL FIN INSPECTION PLATE ATTACHMENT |
| SL-AG-84 |
TAIL WHEEL SHOCK STRUT MODIFICATION |
| SL-AG-85 |
ENGINE MANIFOLD PRESSURE GAGE MODIFICATION |
| SL-AG-86 |
OIL SUPPLY HOSE REPLACEMENT |
| SL-AG-87 |
SHOULDER HARNESS AND INERTIA REEL INSTALLATION |
| SL-AG-88 |
FLYING WIRE BRACKETS INSTALLATION |
| SL-AG-89 |
VOLTMETER REPLACEMENT |
| SL-AG-90 |
ELEVATOR TRIM TAB PUSH-ROD REPLACEMENT |
| SL-AG-91 Rev 1 |
BRAKE MASTER CYLINDER REPLACEMENT |
| SL-AG-92 |
CARBURETOR AIR TEMPERATURE INDICATOR AND IMPROVED EXHAUST SYSTEM INSTALLATION |
| SL-AG-93 |
STARTER TORQUE LIMIT INSPECTION AND/OR STARTER REPLACEMENT |
| SL-AG-94 |
ELECTRICAL SYSTEM MODIFICATION |
| SL-AG-95 |
MULTIPLE AIRWORTHINESS CERTIFICATION PROCEDURES |
| SL-AG-96 |
FUSELAGE UPPER LONGERON INSPECTION |
| SL-AG-97 Rev 1 |
LOWER WING SPAR INSPECTION |
| SL-AG-99 |
WING RIB REPAIR |
| SL-AG-100 Rev 1 |
WING RIB REPAIR |
| SL-AG-102 |
STARTER WIRING IMPROVEMENT |
| SL-AG-104 |
FIREWALL FUEL FILTER DRAIN ACCESS HOLE ENLARGEMENT |
| SL-AG-105 |
ENGINE AIR INLET SCREEN INSPECTION |
| SL-AG-106 |
INSPECTION OF INLET BOWL COUNTERSUNK SCREWS |
| SL-AG-106 |
INSPECTION OF INLET BOWL COUNTERSUNK SCREWS |
| SL-AG-106 |
INSPECTION OF INLET BOWL COUNTERSUNK SCREWS |
| SL-AG-107 |
BATTERY VENT SYSTEM PLASTIC TEES INSPECTION |
| SL-AG-108 |
FLAP TORQUE SHAFT ASSEMBLY INSPECTION |
| SL-AG-109 |
TORQUE CHART UPDATE |
| SL-AG-110 |
WING SPAR STATUS UPDATE |
| SL-AG-111 |
ENGINE MOUNT AND MOUNT ISOLATOR INSPECTION AND REPAIR |
| SL-AG-112 |
FAIRINGS |
| SL-AG-113 |
FLAP LIGHT NUTS RUBBING FLAPS |
| SL-AG-114 |
Fuel Filter Installation Compliance Check |
| SL-AG-115 |
GE Aviation Turboprop H80-100 Engine Fuel Filtration |
| SL-AG-105 |
ENGINE AIR INLET SCREEN INSPECTION |
| SL-AG-96 |
FUSELAGE UPPER LONGERON INSPECTION |
| SL-AG-105 |
ENGINE AIR INLET SCREEN INSPECTION |
| SL-AG-105 |
ENGINE AIR INLET SCREEN INSPECTION |